• Driving one of these old Flat Windows 64 G-10 Panel

    Well, finally had the time to drive my 64 Flat Window, "BABY DOLL".

    Let me say first, this little van drives like a dream; no shake, no shimmy, no hopping. Smooth as silk even over rough asphalt. Can't hardly hear her run, except on first start up, and everything works....but no radio. Steering is rock solid. Just point and that's where she goes.

    Funny non-stock color...almost a burnt Butterscotch or like a watered down glass of scotch & water...one that the ice has melted in.

    1st gear 0-27
    2nd gear 25-55
    3rd gear 50-75 (speed drops between shifts, she's a brick in the wind).

    But I wasn't trying to kill her, just wanted to see what she could do if I need to get out of the way of something (like a mad husband or upset girlfriend). Ha! Cruised 50 miles, nonstop, at 70-75. No problem, no strain. Turned around and did it again. She will go faster than 75, but at that speed I worried about the brakes since I was in freeway traffic (and sober).

    After not having driven a G-10 in 20 plus years, the first thing I noticed was that when you sit behind the steering wheel it feels like you just got into a really big bread box....which is funny because when you first look at the exterior she seems really small. And not being used to starting a carburetored engine (235)......that takes some getting use to. No hit the key and drive off. Taking off from a red light takes some time to get used to, but after a little drive time that comes back to you, especially if you have ever driven a carburetored engine with a standard transmission before.

    When you first close that big old driver's door, it sounds like you just have been in a small fender bender. No sound deadner in these old girls. Had to shut the door twice to make sure, but she was solid.

    You also have to remember to turn later and quicker when making right turns. That comes back to you pretty quick, but makes the eyes on people that have never ridden in a G-10 look alive as they stare at you. The only complaint I have is those big old mirrors, 6X12 dual arms....they've got to go....[they] make too many blind spots when turning left.

    Since it was about 100ยบ outside, the door windows were open; the firewall vent was open.
    70 mph, at a solid cruise, I thought to myself "it is just like riding my motorcycle with a windshield and no helmet on my head"..... it was really kind of nice since this is the first vehicle I've owned in a long time with no AC (roughing it).

    I originally was going to cut her all up: Mustang II front, power rack, V6 4.3, automatic, 4 wheel disc brakes, and dual AC. Now, I don't know. She maybe too good of a van to change. She has a lot of character and she is fun to drive if you like old and mellow.

    Well, time will tell, but in the mean time it's back to "Keep on Truckin' On".

    Going to drive her some more before I do anything stupid.

    Charley

    Attachment 2171
    This article was originally published in forum thread: Driving one of these old Flat Windows. (Baby Doll) 64 G-10 Panel started by Charles Linsenbarth View original post
  • Recent Forum Posts

    madillow

    Strange issue after a few months of Covid hibernation.

    If the bowl is not getting full of fuel due to a clog in the needle and seat or a sticking float, it's possible that when you stop fast, the fuel sloshes

    madillow 04-22-2021, 11:55 PM Go to last post
    tinlizard

    Spindle question

    Seems like it. Although I suppose different bushings might accommodate 2 different king pin diameters in the same hole. But I recall the G10 bushings

    tinlizard 04-21-2021, 10:44 PM Go to last post
    Vanner68

    Spindle question

    The king pin kits are two different part numbers, G20 uses a larger pin. So, I would say the beam is different.

    Rare parts G20 kingpin set

    Vanner68 04-21-2021, 03:18 PM Go to last post
    tinlizard

    1965: Don't Buy a Van Made by Car People!

    I was on a project with Chevrolet commercial vehicles in the late 90s. in a meeting with some mid level brass, one of them revealed that GM's new strategy

    tinlizard 04-21-2021, 08:59 AM Go to last post
    tinlizard

    Spindle question

    Is the actual axle beam different on the 3/4 ton (6 lug) from the 1/2 ton (5 lug) vans? Maybe you (CanVanMan) could just swap out the steering knuckle/spindle

    tinlizard 04-21-2021, 08:47 AM Go to last post