Search:

Type: Posts; User: gfleduc

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    11
    Views
    191

    West Coast 1st Gen Parts

    The bottom 4" or so of the channel post

    41449
  2. Replies
    1
    Views
    48

    We are on Television

    41444
  3. Replies
    5
    Views
    201

    a few parts needed first gen

    Master cylinder covers plugs; Good Used are like hens teeth ...

    Clarks does have them - I don't think it matters much, they have a rubber plug no steel plate.
    You want the 4-1/8"

    I also see...
  4. Replies
    20
    Views
    1,311

    Signal Light Plates

    van-itti - thanks again
    41371
  5. Replies
    24
    Views
    923

    Cargo Door Rod Clip & Lower rod

    P/N reference:
    41361





    FYI: I chased down the P/N history on the rod part numbers. Interesting by 1969 GM went to the same part number for the lower rod on all doors - So I would "assume" ...
  6. Replies
    20
    Views
    1,311

    Signal Light Blank

    van-itti

    The plate came in -Thank-you, it is spot on! I could not wait, I already started to weld the first one in; it is a great fit; if the weld wasn't so bad looking I would have shared a...
  7. Replies
    28
    Views
    1,746

    Front door threshold moldings

    You do nice work!
  8. Replies
    20
    Views
    1,311

    Signal Light Plate

    Nice!
  9. Replies
    20
    Views
    1,311

    Turn Signal Blanks

    NICE!
  10. Replies
    11
    Views
    401

    Trim Plate Stamping

    Thank-you for looking.

    Well, I talked with the guy who does all the "stampings". He enlighten me that it is not stamping but embossing.

    It sounds as if the reverse stamping will not have the...
  11. Replies
    23
    Views
    1,542

    Heater Wiring

    Did you confirm you have continuity between both ends of EACH wire?

    With everything on check voltage.
    a) 12 V into switch
    b) 12 V out of the switch
    b) 12 V into the resistor
    c) 12 V out of the...
  12. Replies
    23
    Views
    1,542

    1st Gen Heater Core

    For you to verify wiring...

    41191
  13. Replies
    11
    Views
    401

    Trim Plate Stamping.

    I measured a TRIM plate; the text size is 3/16" (.187).

    Just for reference - if I am not wrong, the same size as the VIN plate numbers.

    I just got blown away- I found a vendor who does plates...
  14. Replies
    14
    Views
    445

    Doghouse lid latch

    A little correction to a statement prior.

    For 1st gens:
    1964 & "early" 1965 vans had two latches.
    For 1965 "late" & 1966 vans had one centered latch from the factory.

    No - I would not be...
  15. Replies
    11
    Views
    401

    Trim Plate Stamping.

    Dang - good point on the reverse stamping - thank-you
  16. Replies
    11
    Views
    401

    Trim Plate Stamping.

    Hey Gang,

    My trim tag was not present when I bought the van. I am going to make up a blank. I have not found anyone to stamp on the data. Hoping someone on the network here would have a lead...
  17. Replies
    2
    Views
    636

    1965 Shortie - Lancaster,Ca - No Door

    FYI
    I sent the guy a note so he could correct the add to 1965 (not 1966),
    He asked a couple of general questions - He did mention that it is a No door van. I recommended he show a photo of that...
  18. Thread: Question...

    by gfleduc
    Replies
    11
    Views
    483

    Yes it is 41145

    Yes it is

    41145
  19. Thread: Question...

    by gfleduc
    Replies
    11
    Views
    483

    signal stat flarestat 105

    Hy Zack,

    For starters check eBay search on "signal stat" or "flarestat 105" or some combination. I have seen a couple of non van specific units get listed in the last 1/2 year. I have some...
  20. Thread: Question...

    by gfleduc
    Replies
    11
    Views
    483

    Hazzard Switch - Ref OEM

    Per 1965 Catalog: 2.575 986294: 1965 PASS, G10, & Corvette SWITCH UNIT, Haxard Flasher

    41132
  21. Replies
    20
    Views
    1,311

    Front Signal light Blanks

    I am interested - would you have a laser cutter or such for mass production?
  22. Replies
    20
    Views
    1,311

    Front Signal Light Replacment Blanks / Patches

    I heard Matchstick was going to fabricate some front signal light blanks


    41360
  23. Replies
    23
    Views
    1,542

    Heater switch

    P/n 3843526
  24. Replies
    8
    Views
    450

    1st Gen Belly Pan fasteners?

    Thank-you
  25. Replies
    8
    Views
    450

    1st Gen Belly Pan fasteners?

    Would you verify the bolt lengths for me?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4