Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 25

Thread: TCV bracket for 200R on an I6?

  1. #11
    Certifiable Vanatic
    Join Date
    Oct 2016
    Location
    San Diego
    Posts
    766
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by Vanner68 View Post
    Manual Amie doesn't have the same ring to it.
    Good one!

  2. #12
    VCVC Member cruzbox's Avatar
    Join Date
    Dec 2013
    Location
    southside chicago il
    Posts
    687
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Bow tie overdrive

    I have been using there transmission s and TV setups for a lot of years on everything from a SBC vega to a pro street pickup! Let me know if you have any questions
    Cruzbox

  3. #13
    VCVC Member jrinaman's Avatar
    Join Date
    Apr 2011
    Location
    zelienople, pa.
    Posts
    2,389
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by cruzbox View Post
    I have been using there transmission s and TV setups for a lot of years on everything from a SBC vega to a pro street pickup! Let me know if you have any questions
    Cruzbox
    do you know if they make a linkage for either the monojet smiley and amie needs or the webber 32/36 I have? I have seen 'correctors' or holley an edelbrok but not much else.
    '64 chevy, 292 40 over, 206/526 cam, 2004r trans. 9.75:1, dual webbers, Langdon cast headers, 1.94 valves

  4. #14
    VCVC Member Space Truckin's Avatar
    Join Date
    Nov 2010
    Location
    Upland,Ca
    Posts
    1,541
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by jrinaman View Post
    do you know if they make a linkage for either the monojet smiley and amie needs or the webber 32/36 I have? I have seen 'correctors' or holley an edelbrok but not much else.
    I just had BowTie make and install a custom TV cable for the FiTech fuel injection in my 3rd gen. I would give them a call, it was quite painless...JM2C..I could be wrong...ha
    If you're not living on the edge, you're taking up too much space..JM2C...hehehe
    Steve

    1967 Chevy 90 "Space Truckin"
    350 SBC 260hp/ 350tq, MSD HEI, Holley 4150, Sanderson Block Hugger Headers, BowTie 700R4, 3:36 posi

    1973 Chevy 110 "Orange Bang" w emphasis on the BANG :-)
    383 Stroker 440hp/ 480tq, MSD 6AL/ HEI, FiTech, Hooker Full length Headers, BowTie 700R4, 3:73/ Eaton Truetrac, "Cruiseaire" Original

  5. #15
    VCVC Member cruzbox's Avatar
    Join Date
    Dec 2013
    Location
    southside chicago il
    Posts
    687
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    FiTech

    They are great guys to work with, they also modified my FiTech to work with a 700 r in my vega. Also in our 67 van I used there set up to lock up In 2nd or 3rd gear for towing in the hills👍

  6. #16
    Administrator smiley's Avatar
    Join Date
    Apr 2000
    Location
    New Orleans, LA
    Posts
    6,019
    Mentioned
    12 Post(s)
    Tagged
    1 Thread(s)
    Thank you guys for all the input. Iím looking into all this now and Iíll follow up.
    1966 Chevy Display, "Southern Belle"
    1968 Chevy, "Blue Overdose"

  7. #17
    VCVC Charter Member Vanner68's Avatar
    Join Date
    May 2000
    Location
    Kimball MI USA
    Posts
    13,389
    Mentioned
    2 Post(s)
    Tagged
    0 Thread(s)
    I'm contemplating installing this in my trans in the 65.

    https://www.summitracing.com/oh/part...6020/overview/

    The TV cable then only controls shift points not pressure, so I will have a little more breathing room putting an OD trans on an engine that was never paired with one at the factory
    Gregg Groff


    There's no place like 127.0.0.1

    1968 Chevy G20 108 panel Now with 454 power!

    1965 Chevy G10 panel- OHC Pontiac inline 6

  8. #18
    Van Addict dougw1's Avatar
    Join Date
    Mar 2017
    Location
    Bluesky Alberta
    Posts
    92
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by Vanner68 View Post
    I'm contemplating installing this in my trans in the 65.

    https://www.summitracing.com/oh/part...6020/overview/

    The TV cable then only controls shift points not pressure, so I will have a little more breathing room putting an OD trans on an engine that was never paired with one at the factory
    If you go this route keep us informed as to how it works for you. I'm dreading the cable adjustment as well when I get the motor & trans in.

  9. #19
    VCVC Charter Member Vanner68's Avatar
    Join Date
    May 2000
    Location
    Kimball MI USA
    Posts
    13,389
    Mentioned
    2 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by dougw1 View Post
    If you go this route keep us informed as to how it works for you. I'm dreading the cable adjustment as well when I get the motor & trans in.
    Will do, but at the rate I get time for my projects it may be awhile...
    Gregg Groff


    There's no place like 127.0.0.1

    1968 Chevy G20 108 panel Now with 454 power!

    1965 Chevy G10 panel- OHC Pontiac inline 6

  10. #20
    VCVC Member cruzbox's Avatar
    Join Date
    Dec 2013
    Location
    southside chicago il
    Posts
    687
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Adjusting TV cable

    Itís very straight forward, hook up a pressure gage to the side of the trans with a 90degree fitting ( look at Bowtie overdrive website) and go through the instructions. Very easy to deal with. No black magic involved!
    Cruzbox

User Tag List

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •