Page 5 of 6 FirstFirst ... 3456 LastLast
Results 41 to 50 of 53

Thread: srarted a new project

  1. #41
    VCVC Member BILLS66's Avatar
    Join Date
    Feb 2007
    Location
    Salem,OR
    Posts
    2,656
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    You are very talented ! nice work I envy you ! Bill
    1966 Chevy G10 Panel, 283 small block/turbo 350,Disc brakes

  2. #42
    VCVC Member rarechev's Avatar
    Join Date
    Mar 2013
    Location
    Ontario,Canada
    Posts
    359
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    thanks for the kind words and likes guys! it helps to keep me going.
    1970 108 panel, 350, 700R4, power tilt steering, power brakes, power windows
    1969 90 panel

  3. #43
    VCVC Member SAVAGE's Avatar
    Join Date
    Feb 2004
    Location
    FT. WAYNE IN.U.S.A.
    Posts
    3,194
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Question

    Dan, what are you useing for your outside gas filler panel??(does that make any senses??)
    Tom

  4. #44
    VCVC Member rarechev's Avatar
    Join Date
    Mar 2013
    Location
    Ontario,Canada
    Posts
    359
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Smittybilt 7508 - Gas Filler Housing, Chrome Part #7508 for a jeep
    1970 108 panel, 350, 700R4, power tilt steering, power brakes, power windows
    1969 90 panel

  5. #45
    VCVC Member rarechev's Avatar
    Join Date
    Mar 2013
    Location
    Ontario,Canada
    Posts
    359
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    got back at it and done some work on the right side rear. I didn't want to spend $400 on the quarter panel so I cut out a piece of the old roof section and made a lower panel.
    Attached Thumbnails Attached Thumbnails IMG_2014.jpg   IMG_2026.jpg   IMG_2025.jpg  
    1970 108 panel, 350, 700R4, power tilt steering, power brakes, power windows
    1969 90 panel

  6. #46
    VCVC Member cruzbox's Avatar
    Join Date
    Dec 2013
    Location
    southside chicago il
    Posts
    760
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    More nice work!

    Looking good. another hole patched, next!
    cruzbox

  7. #47
    VCVC Member rarechev's Avatar
    Join Date
    Mar 2013
    Location
    Ontario,Canada
    Posts
    359
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    had some pin holes in the passenger side floor overlap so I welded in some new metal. also making some windowless doors out of the old windowed doors off my other van.
    Attached Thumbnails Attached Thumbnails IMG_2031.jpg   IMG_2030.jpg   IMG_2027.jpg  
    1970 108 panel, 350, 700R4, power tilt steering, power brakes, power windows
    1969 90 panel

  8. #48
    VCVC Member
    Join Date
    Jul 2004
    Location
    Sacramento, Ca,USA
    Posts
    2,703
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)
    What welder are you using and at what settings?
    108VanGuy...
    1969 Chevy Panel, 250 CID, 3 Spd.with OD, 3.36 "WedgieVan" Daily Driver
    1967 Chevy Panel, 230 CID, 3 Spd. 3.36 "UtiliVan" 292 TFI coming. Owned since 76
    1964 GMC Panel, 194 CID, 3 Spd. "CrunchoVan"
    1965 GMC HandiBus Custom, 194 CID, 3 Spd. "MilkVan" Seized Engine
    1965 Chevy Panel 350 CID, 3 Spd. "RustoRoof" Runs but wiring bad
    1969 Chevy 108 Display 307 CID THM 350 Power Brakes 3.73 Posi
    1965 Chevy Panel, V8, 3 Spd. "Gold Hills Van" Best body of my 65s
    1965 CamperVan, V8, 3 Spd.

  9. #49
    VCVC Member rarechev's Avatar
    Join Date
    Mar 2013
    Location
    Ontario,Canada
    Posts
    359
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Mark my welder is a decastar 180.For sheet metal I weld at #2 , #1 if I am getting burn through.
    Attached Thumbnails Attached Thumbnails IMG_2033.jpg   IMG_2032.jpg  
    1970 108 panel, 350, 700R4, power tilt steering, power brakes, power windows
    1969 90 panel

  10. #50
    VCVC Member
    Join Date
    Jul 2004
    Location
    Sacramento, Ca,USA
    Posts
    2,703
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    If

    If I ever get to Ontario, Id appreciate a welding lesson. I could sure use it! Just ask Freaky.
    108VanGuy...
    1969 Chevy Panel, 250 CID, 3 Spd.with OD, 3.36 "WedgieVan" Daily Driver
    1967 Chevy Panel, 230 CID, 3 Spd. 3.36 "UtiliVan" 292 TFI coming. Owned since 76
    1964 GMC Panel, 194 CID, 3 Spd. "CrunchoVan"
    1965 GMC HandiBus Custom, 194 CID, 3 Spd. "MilkVan" Seized Engine
    1965 Chevy Panel 350 CID, 3 Spd. "RustoRoof" Runs but wiring bad
    1969 Chevy 108 Display 307 CID THM 350 Power Brakes 3.73 Posi
    1965 Chevy Panel, V8, 3 Spd. "Gold Hills Van" Best body of my 65s
    1965 CamperVan, V8, 3 Spd.

User Tag List

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •