Search:

Type: Posts; User: Vanner68

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    5
    Views
    292

    Facebook is not a forum

    Forums are better.
    I don't post much here, pretty much just when I see a problem that I know the solution to.

    And that is where forums rule.

    Example:
    Today on facebook, someone posted about...
  2. GM vehicle information kit

    Here's the original data for the van from GM. 1968-70 are identical

    https://www.gmheritagecenter.com/docs/gm-heritage-archive/vehicle-information-kits/G-Van/1969-Chevrolet-G-Van.pdf
  3. Replies
    69
    Views
    4,016

    Got mine yesterday, they look mahhvelous! ...

    Got mine yesterday, they look mahhvelous!

    https://i.pinimg.com/originals/19/04/b1/1904b165f5001d55d8829f1dc93059a8.jpg
  4. Replies
    69
    Views
    4,016

    Sent paypal for one of each

    Sent paypal for one of each
  5. Replies
    6
    Views
    258

    That's a good habit to have, but in this case...

    That's a good habit to have, but in this case we're just pulling fuses. There is still a complete circuit even with the meter on the negative cable. In either case, shorting anything out is going to...
  6. Replies
    6
    Views
    258

    Get a multimeter with a 10 amp scale (like this...

    Get a multimeter with a 10 amp scale (like this https://www.homedepot.com/p/Commercial-Electric-Manual-Ranging-Multimeter-MMM-8301S/305089516 )

    Disconnect the positive cable from the battery and...
  7. Replies
    69
    Views
    4,016

    How much for one 1st gen and 1 2nd gen?

    How much for one 1st gen and 1 2nd gen?
  8. Thread: Doc Yukon

    by Vanner68
    Replies
    8
    Views
    389

    RIP It was nice to see him at the last VCVC...

    RIP

    It was nice to see him at the last VCVC rally.
  9. Replies
    13
    Views
    1,007

    That's ridiculous. $6k was a bit much for that...

    That's ridiculous. $6k was a bit much for that van. Lots of sketchy work, and I know sketchy work because I've done sketchy work while learning....
  10. Replies
    4
    Views
    285

    A good slam on the brakes should do that, but in...

    A good slam on the brakes should do that, but in my experience (crusty old vans) it's often frozen in place.
  11. Replies
    4
    Views
    285

    If disconnecting the wire from the proportioning...

    If disconnecting the wire from the proportioning valve turns the light off, and the brakes work fine otherwise, then the switch in the prop valve is bad.
  12. Replies
    13
    Views
    1,007

    At least the 'builder' didn't paint it as a...

    At least the 'builder' didn't paint it as a Mystery Machine clone.
  13. Replies
    13
    Views
    1,007

    Everything underneath that van needs to be...

    Everything underneath that van needs to be redone, and probably most of what's up top as well.

    Needs airbags and air shocks just to mask the completely sagged out springs, inner rockers are hunks...
  14. Replies
    11
    Views
    624

    The king pin kits are two different part numbers,...

    The king pin kits are two different part numbers, G20 uses a larger pin. So, I would say the beam is different.

    Rare parts G20 kingpin set part # RP30445

    Rare parts G10 kingpin set part #...
  15. The beginnings of the myth that GMC trucks were...

    The beginnings of the myth that GMC trucks were more 'trucky' than Chevrolets
  16. Replies
    11
    Views
    624

    The spindles are different for the 6 lug, only...

    The spindles are different for the 6 lug, only way to go 6 lug is replace the entire front axle. No other vehicle shares front end parts with our vans.
  17. Replies
    4
    Views
    293

    This is probably not what you want to hear, but...

    This is probably not what you want to hear, but here goes:

    Every time I have a fuel gauge issue, I bite the bullet and drop the tank.

    Remove the sender, remove the gauge and bench test with...
  18. Replies
    9
    Views
    1,022

    RIP

    RIP
  19. Replies
    13
    Views
    1,136

    let's see if photobucket links work...

    https://hosting.photobucket.com/albums/v230/Vanner68/68%20chevy/69chevyandbike.png?width=1920&height=1080&fit=bounds
  20. Replies
    5
    Views
    582

    Most DIY conversions total cost comes in around...

    Most DIY conversions total cost comes in around $35,000.

    I would expect a turnkey conversion to be $50k-$60k

    That said, if one is creative, it can be done for less. Rich Rebuilds on youtube did...
  21. Replies
    9
    Views
    689

    For one, King City is not affiliated with the...

    For one, King City is not affiliated with the National Truck-In Board, which handles the Van Nationals, those are different events.
    The Van Nationals generally has 400-600 vans in attendance.
  22. Replies
    2
    Views
    308

    YouTube channel

    As this progresses, it will be uploaded to my new YouTube channel, Derelict Garage.

    Here's a short intro video

    https://youtu.be/Ns7b04W0f48
  23. Replies
    2
    Views
    308

    Thunderkiss 65 update

    https://hosting.photobucket.com/albums/v230/Vanner68/65%20Chevy%20Van/IMG_20161124_230647_zpsw7cl1adp.jpg

    I'll be honest, I'm kinda at an impass on the 68 G20 6 lug brakes, so when the warm...
  24. GodIhatePhotoshop

    GodIhatePhotoshop
  25. Or....

    someone in British Columbia wanted another project....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4